Hp Tape Library Error Codes
Some tapes need to be inserted and removed several times to condition them for free movement in and out of the magazine. If the volumes are compressed, make sure that the backup software does not uncompress the data on read and has hardware and software compression disabled. The recommended number of disks per Ultrium tape drive is: Ultrium 448: 6 Ultrium 920: 15 Ultrium 1760: 20 Also, make sure that the server or workstation is used as little Check all parallel SCSI and power connections and confirm that the unit is attached to a valid SCSI SE or LVDS bus. weblink
Damage or misplaced labels on the cartridge could have caused the load/unload failure. Clean the tape drive. Here is a brief description of a few parts listed in the table below: Gripper: The part of the robotics assembly that pinches media in order to grip it. sub-code indicates which fan is affected. http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c00574301
He Cannot Initialize Barcode Reader Code 80 01
Everything shows all events. top top Backup server The backup server must have enough RAM and processor power to transfer the files from the disk to the tape drive. Do not connect the device to an arrow SCSI bus.
Click the Health button on the main toolbar to generate and display a standard report. View device and drive error logs. Verify that the proper device driver is installed for the SAS host adapter. He Elevator Blocked Error During Move Elevator To Scan Position Code 8b 26 The more time the disks are seeking to files, the lower the performance.
Remove the magazines, re-seat them, and try again. Msl4048 Error Codes The LCD displays an error code. Check the length and integrity of the SCSI cabling. http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c00768254 A0 Sled range of motion out of specification NOTE: Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive.
Lots of small files require the disk to perform many random accesses instead of a continuous read. Ibm Ts3100 Tape Library Error Codes Once the tape is rewound, the eject cycle will take fewer than 16 seconds. Retry the operation with a different, known good tape. Run the wellness test 90 Ends of elevator movement not in expected range Run the wellness test 91 Ends of rotation movement not in expected range 92 Ends of sled movement
Msl4048 Error Codes
Secure the terminator by tightening the finger-screws until snug. http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c00581506 Elevator: The part of the robotics assembly that moves in the vertical direction. He Cannot Initialize Barcode Reader Code 80 01 Change the Startup type to Disabled and click OK. He Slider Blocked Error During Second Slider Movement Code 8a 63 Tape movement problems Problem Solution Tape stuck in drive.
DB External cooling fan error (fan motion has stopped). http://upintheaether.com/error-codes/ibm-db2-sql-error-codes.php Secure the terminator by tightening the finger-screws until snug. Make sure that the cartridge is compatible with the drive. Slider: The part of the robotics assembly that plunges in and out for get and put operations. He Sled Position Not Found Code 9b 37
If the RMI web page does not display, ping the device’s IP address. top Novell You might need to tweak some Novell operating system parameters to achieve good backup performance. Reload the magazines with tapes that have passed inspection and new tapes to replace cartridges that did not pass inspection. check over here None.
Make sure that the appropriate data cartridge for the model is being used. Msl2024 Contact technical support. Third code - The sub-code (62 in this example).
Inspect it for damage.
Check if the fan is operational and not obstructed F0 Drive exceeded temperature specification Check ambient temperature conditions and fans F1 Autoloader controller lost communication with the drive Re-seat the tape Do not backup when the database is in heavy use. Cleaning process could not be performed. For example: 1:00 p.m.
To generate and view a report or support ticket from L&TT: In the L&TT By Product or By Connection tab, select the device from the device list. Check the length and integrity of a parallel SCSI cabling. Sign-in Register Site help Skip to ContentSkip to FooterSolutions Transform to a Hybrid Infrastructure Protect Your Digital Enterprise Empower the Data-Driven Organization Enable Workplace Productivity Cloud Security Big Data Mobility Infrastructure this content Use the magazine removal process to release the magazine and remove it from the device.
To check the overall operation of the device, run the wellness test from the RMI or OCP. Stop as many programs as possible while a backup or restore is in progress. NOTE: Many backup applications use their own drivers. For good performance, use a faster connection with LTO-3 and LTO-4 tape drives.
If the connector on the cable is keyed in a different location, not only will the connector not plug in, but the cable probably will not work. If you are unsure of the speed of the HBA or switch that the Library is connected to, try Automatic (on the RMI) or Auto Detect (on the OCP) option. Update the Library to the latest version. NOTE: The support ticket downloaded from the RMI will only contain information about the Library.
D0 ROM checksum incorrect Retry Library firmware upgrade. Everything shows all events. If the server configuration does not support changing addresses, try using the Hard Auto-Select option for the Loop mode. If the application software or operating system does not communicate with the device after installation, determine the extent of the detection problem: Does the application software detect the tape drive?
Device Driver Installation: Make sure that the proper device driver, if applicable, is installed for the device. Check if the fan is operational and not obstructed F0 Drive exceeded temperature specification Check ambient temperature conditions and fans F1 Library controller lost communication with the drive Re-seat the tape Unless otherwise listed in Operation problems , try to resolve the error by cycling power to the device and retrying the operation. For a list of compatible SCSI host bus adapters and application software, check with the SCSI host adapter manufacturer, backup application vendor, or the HP support website at http://www.hp.com/go/ebs .
LTO-3: MARGINAL. top Main error code descriptions Main error codes Error Code Description Details and Solution 80 Can not initialize bar code reader Power-cycle the unit and retry the operation 81 No response top Performance Problems Click here to view HP StorageWorks MSL4048 Tape Library - Performance Problems . Unless otherwise noted in the troubleshooting document, try to resolve the error by cycling power to the library and retrying the last operation.
To improve performance when backing up data from a database: Use specific backup agents for the database. No change is necessary but using a sequential backup method, such as an image backup, could offer some performance gains. Before installing a driver, make sure it is not in conflict with the application software.