Home > Error Codes > Hp Storageworks Msl4048 Error Codes

Hp Storageworks Msl4048 Error Codes

Contents

Contact technical support. Check ambient temperature conditions. Library error sub-codes The following table lists the library error sub-codes. top Provide feedback Please rate the information on this page to help us improve our content. weblink

DD Power supply fan has failed, redundancy may be at risk. Expand the event for more information (as shown in Figure 3). Insert a USB flash drive into the USB port on the rear panel and then from the OCP, select Download support ticket to USB. Check that it is connected correctly to Port A of the tape drive. http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c01517702

He Cannot Initialize Barcode Reader Code 80 01

DB External cooling fan error. Figure 2: Support ticket in viewer Expand HP Event Logs to see events divided into three categories: Events in the last 24 hours Events in the last 31 days Events older CAUTION: Shipping Lock: The shipping lock must be removed for the robotics to work properly on the MSL4048. The available logs are: Error Trace, Informational Trace, Warning Trace, Configuration Change Trace and Standard Trace.

The main error code (0x83) is displayed in parenthesis as the Global error code. B5 Robotic controller not responding to command from Library controller Reset the device and retry the operation. It could be a defective cartridge. He Elevator Blocked Code 8b 26 The error sub-code 00 indicates drive 1, sub-code 01 indicates drive 2, and so on.

The subcode indicates which drive sled fan is affected. He Slider Blocked Error During Second Slider Movement Code 8a 63 If the error persists, contact the support personnel. To view a downloaded support ticket, perform the following steps: From the L&TT File menu, select Load Support Ticket. http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c01517695 There are three ways to obtain error codes from the device: On the OCP On the RMI On an L&TT support ticket or report top Finding error code information on the

For example, 1:00 pm is 13:00.D7 is the main error code50 is the error sub-code top Finding error code information on the RMI You can find error codes on the RMI Hp Tape Library Error Codes Unless otherwise noted in the troubleshooting document, try to resolve the error by cycling power to the library and retrying the last operation. Very helpful Somewhat helpful Not helpful End of content United StatesHewlett Packard Enterprise International Start of Country Selector content Select Your Country/Region and Language Click or use the tab key to Rotation: The part of the robotics assembly that turns the robot to face each magazine and the drive.

He Slider Blocked Error During Second Slider Movement Code 8a 63

Elevator is the part of the robotics assembly that moves in the vertical direction. Ensure that nothing is obstructing the opening of the mailslot. He Cannot Initialize Barcode Reader Code 80 01 Ensure that nothing is stacked on top of the device because any weight on top of the device can bow the top cover down and interfere with the robotics. He Elevator Blocked Error During Move Elevator To Scan Position Code 8b 26 Run advanced diagnostic tests, including connectivity, read/write, media validation, and testing the functionality of the library.

Thank you! http://upintheaether.com/error-codes/ibm-ps2-error-codes.php top Detection problems after installing a parallel SCSI device Problems encountered after installation are often caused by improper parallel SCSI bus configuration, application software configuration errors, or an incorrectly configured operating Re-seat the tape drive to ensure a good connection to the device. Look at the device analysis results for additional information about the device's operation. He Sled Position Not Found Code 9b 37

If the device was moved, verify that each of the tape cartridges is properly seated in a magazine. 8A Slider obstructed Run the wellness test. Check if the fan is operational and not obstructed DC I2C Bus failure. D1 RAM error during Power-On-Self-Test Power-cycle the unit D2 Read or Write to NVRAM on Library controller failed D3 Time controller failed during Power-On-Self-Test D4 Internal UART serial communication error D5 check over here The top of the support ticket contains basic configuration information about the device (as shown in Figure 2).

If this error occurs with sub-code 43, a magazine could be misaligned. Mechanical Block Code 8d 07 Ibm If an error occurs during operation, the device stops the current operation and displays an error code on the LCD screen. sub-code 00: drive sled #1, sub-code 01: drive sled #2 NOTE: Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive.

Here are some terms that you would encounter in the table below (Main error codes): Gripper: The part of the robotics assembly that pinches media in order to grip it.

While holding the paper clip, have a second person attempt to pull the magazine out of the front of the unit. The log entries are displayed in order of most recent to oldest. Does the operating system detect the Library? Ibm Ts3200 Error Codes Initiate the firmware upgrade process before loading a firmware upgrade tape into the drive. 64 Invalid cleaning cartridge.

Drive has rejected the cartridge as invalid. C2 Web server initialization failed C6 Ping command did not reach target C7 Cannot upgrade firmware from USB Retry the firmware upgrade. If the application software or operating system does not communicate with the device after installation, determine the extent of the detection problem: Does the application software detect the tape drive? this content The MSL4048 can also be set on a flat surface when mounted in the optional Rack-to-Tabletop Conversion Kit.

Run the wellness test. If the failure remains with the same slot, the magazine may be at fault. Run advanced diagnostic tests, including connectivity, read/write, media validation, and testing the functionality of the device. Operating the Library without one of these kits, such as on a flat surface without the Rack-to-Tabletop Conversion Kit, could result in device errors.

The default SCSI ID for each tape drive will be 4 or 5 depending on the Library model and drive slot.