Home > Error Codes > Hp Msl4048 Error Codes

Hp Msl4048 Error Codes

Contents

If there are still issues, change the port type to Auto Detect. Text Quote Post |Replace Attachment Add link Text to display: Where should this link go? top Detection problems after installing a parallel SCSI device Problems encountered after installation are often caused by improper parallel SCSI bus configuration, application software configuration errors, or an incorrectly configured operating Thank you in advance. 0 Kudos Reply Contact Privacy Policy Terms & Conditions ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the navigate here

Make sure that the proper device driver is installed for the parallel SCSI host adapter. NOTE: Many backup applications use their own drivers. Refer to the manuals supplied with the other devices on the parallel SCSI bus for information on enabling or disabling termination on those devices. If the application software or operating system detects the tape drive, but not the Library: Verify that multiple LUN support is enabled on the HBA. click resources

He Cannot Initialize Barcode Reader Code 80 01

FC cables are delicate. The MSL4048 can also be set on a flat surface when mounted in the optional Rack-to-Tabletop Conversion Kit. Verify that the fan for the indicated fan is operational and not obstructed.

Check the length and integrity of your SAS cabling. Does the operating system detect the tape drive? Based on the extent of the detection problem, check the following: If neither the application software nor operating system detects the tape drive, or they do not detect both the tape He Elevator Blocked Code 8b 26 If the application software or operating system does not communicate with the device after installation, determine the extent of the detection problem: Does the application software detect the tape drive?

If the connector on the cable is keyed in a different location, not only will the connector not plug in, but the cable probably will not work. He Slider Blocked Error During Second Slider Movement Code 8a 63 This allows the system to select an available address when it first connects, and retain that address for future connections. Creating your account only takes a few minutes. http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c01517695 If the cable has been bent or twisted sharply, it may be broken and must be replaced.

Drive has rejected the cartridge as invalid. Hp Tape Library Error Codes Is this info coming from the machine your library is connected to or from the web interface of they library itself? Everything was working fine up until last week. Verify that the power supply is inserted correctly and that the thumbscrews are adjusted.

He Slider Blocked Error During Second Slider Movement Code 8a 63

I am 100% sure I can get rid of the error associated with the acutal drive but am unable to do the same with cartridges. 0 Kudos Reply Managed to get navigate to these guys The HP Library & Tape Tools diagnostic provides an intuitive graphical user interface with integrated context-sensitive help. He Cannot Initialize Barcode Reader Code 80 01 CAUTION: This Library is designed to operate when installed in a rack using the included rack rails. He Elevator Blocked Error During Move Elevator To Scan Position Code 8b 26 Power cycle the unit.

For half-height drives, the default SCSI address for the bottom drive in each full-height drive bay is 4 and the default SCSI address for the top drive is 5 as shown check over here The device uses two Logical Unit Numbers (LUNs) to control the tape drive (LUN 0) and robotic (LUN 1). Does the operating system detect the Library? Help Desk » Inventory » Monitor » Community » Veritas.com Support Veritas Open Exchange Login or Join Communities Information Governance Backup and Recovery Business Continuity Partners Inside Veritas Vision 2016 Developers He Sled Position Not Found Code 9b 37

Check that it is connected correctly to Port A of the tape drive. Subcode 00: drive sled #1 Subcode 01: drive sled #1 Verify that the fan for the indicated fan is operational and not obstructed. For full-height tape drives the default SCSI address is 4. his comment is here As for your problem at hand, I believe the info on the library itself will be able to shed more light of the goings on of the drive and library and

Make sure that the cartridge is compatible with the drive. Mechanical Block Code 8d 07 Ibm Also forget about Backup Exec for a minute and see if you can download some HP tape tools and just be confident that the library is working so you know if Verify that an HBA is supported by the host computer and qualified with the Library.

You should contact HP to sort out these problems 0 Kudos Reply ...that points to the CraigV Moderator Partner Trusted Advisor Accredited ‎09-03-2014 05:33 AM Options Mark as New Bookmark Subscribe

It could be a defective cartridge. Before installing a driver, make sure it is not in conflict with the application software. Drive has rejected the cartridge as invalid. Ibm Ts3200 Error Codes Also, if any SE devices are on the same parallel SCSI bus, all of the devices on the bus slow down to SE speed, which severely degrades performance.The Library is NOT

The device requires an HBA with multiple LUN support and multiple LUN support must be enabled on the host computer. If you are unsure of the speed of the HBA or switch that the Library is connected to, try Automatic (on the RMI) or Auto Detect (on the OCP) option. The errors had gone, the inventory task in BEXEC worked and all was fine. http://upintheaether.com/error-codes/ibm-ps2-error-codes.php Check your software provider's website for the latest drivers and patches.

Make sure that the host adapter is properly seated in the motherboard slot and the operating system correctly detects the host adapter. Initiate the firmware upgrade process before loading a firmware upgrade tape into the drive. 65 Invalid upgrade cartridge. Verify that the cartridge is not a firmware upgrade tape. NOTE: Many backup applications use their own drivers.

Refer to the manual that came with a parallel SCSI host adapter for installation and troubleshooting instructions. Your cache administrator is webmaster. The confusing part was that some of the bad tapes it originally reported were OK, some of the originally reported bad tapes were in error and tapes that originally did not Your cache administrator is webmaster.

I find the latter always provides me with much more meaningful information. 0 Anaheim OP technumber5 May 2, 2014 at 7:55 UTC This is coming from the machine Must warn you that this is something I vaguely and did not do any research before telling you this. Thanks Error 3.JPG ‏60 KB error2.JPG ‏58 KB Error 4.JPG ‏115 KB Error 1.JPG ‏63 KB Labels: 2010 Backing Up Backup and Recovery Backup Exec Error messages Run advanced diagnostic tests, including connectivity, read/write, media validation, and testing the functionality of the device.

Sign-in Register Site help Skip to ContentSkip to FooterSolutions Transform to a Hybrid Infrastructure Protect Your Digital Enterprise Empower the Data-Driven Organization Enable Workplace Productivity Cloud Security Big Data Mobility Infrastructure Since moving to unitrends we haven't had a single hiccup writing tapes. A data cartridge may have been loaded instead of a cleaning cartridge. It could be a defective cartridge.

Pay particular attention to any steps describing configuration settings. If the screen shows Logged Out: Check that the Fibre speed is set to Automatic (on the RMI) or Auto Detect (on the OCP), or that the correct fibre speed is The cable is damaged. Based on the extent of the detection problem, check the following: If neither the application software nor operating system detects the tape drive, or they do not detect both the tape

Upgrade the Library firmware to the latest release. Exchange the cleaning tape. 63 Invalid cartridge. View device and drive error logs. I will have to take a look at Unitrends appliance. 1 Anaheim OP technumber5 May 19, 2014 at 8:11 UTC I'm thinking it be a good idea to