Home > Error Codes > Hp Eio Error Codes

Hp Eio Error Codes

Contents

If the Help topic is longer than four lines, use (Up Arrow) or (Down Arrow) to scroll through the entire topic. Figure 33: Opening and closing the top cover If a jam message persists, it is possible that jammed paper is still in the printer. top 13.12.08/13.12.09, 13.12.10/13.12.11 JAM IN OUTPUT DEVICE Description Jam in the output device (stapler stacker of stacker). Watch the termination's on the network cabling. Check This Out

Press GO to resume printing. Action NOTE: Press the ? (help) button for detailed information about clearing the jam. If worn, replace. Push the blue levers upward and pull the fuser straight out of the printer.

Hp Error 49

Figure 58: Loading paper Make sure that the stack is flat at all four corners and that the top of the stack is below the maximum-height indicators. Figure 28: Closing the rear door If the error persists replace the stapler/stacker or stacker. If the error 66.12.03 persists, replace the stapler unit. Figure 40: Inserting fuser Install the rear output bin.

top 79.XXXX PRINTER ERROR To continue turn off then on Description The printer detected a critical hardware error. Reduce the complexity of the print job to avoid the error. If jammed paper is present, remove it. 49 Error Hp Laserjet P2055dn Reseat the EIO card.

Figure 38: Removing the fuser Remove the jammed paper. Hp Printer Error Codes List Be careful not to spill it on yourself or into the printer.) NOTE: NNOTE: If the jammed paper is difficult to remove, try opening the top cover all the way to Make sure it locks into place. this website This is typically an e-label issue.

Slide the print cartridge into the printer as far as it can go. Hp Printer Error 49 4c02 top 41.X PRINTER ERROR For help press ? Back Error 12 Printer Open Paper path door (IIP/IIIP) or top cover open. top Additional information To print a configuration page at the control panel Press (Select) to open the menus.

Hp Printer Error Codes List

HP LASERJET 4250 ERROR 60.02 Q:  I have an hp laserjet 4250 error 60.02 that wont seem to go away.  What causes this error 60.02? https://www.marketpoint.com/hp-printer-error-codes.aspx Replace the network card if needed. 5. Hp Error 49 Turn the image adapt and page protect to ON or AUTO either from the control panel or from within HP Explorers Remote Control Panel. 5P/5Si Same as above, Press GO to Hp Computer Error Codes If the error does not clear, turn the printer power off and then turn the printer power on.

Try printing a job from a different program. http://upintheaether.com/error-codes/ibm-ps2-error-codes.php Figure 1: Opening top cover and removing print cartridge Use the green handle to lift the paper-access plate. Also try printing from a different application. This pad needs to provide friction to the feeding paper. Hp Laptop Error Codes

LJ 5100 A temporary printing error occurred. Power cycle the printer. ERROR 41-X X= 1,2,4,5 A temporary error occured - Press "CONTINUE" to clear. 41.3 Error - Unexpected paper size - more than one sheet of paper picked up. this contact form Look for the jam in another location, contact HP, or contact an authorized service provider.

Very helpful Somewhat helpful Not helpful End of contentUnited StatesHP WorldwideStart of Country / Region Selector contentSelect Your Country/Region and LanguageClick or use the tab key to select your countryArgentinaAustraliaBelgiqueBoliviaBrasilCanadaCanada-françaisČeská republikaChileColombiaDeutschlandEcuadorEspañaFranceIndiaIrelandItaliaMagyarországMéxicoNew Error 49 Hp Laserjet Pro 400 Replace if defective An abnormal connection break may have occurred during data transfer - Press Continue or Go to clear this error message. After performing the actions above, press GO.

The control panel will display SELECT LANGUAGE .

ERROR CODES HP laserjet 4250 error 21 Printer cannot process the page quickly enough Hp laser 4250 error 22 eio Printers eio card in the slot has overflowed its I/O Figure 53: Sliding the cover until it clicks Reattach any cables and the power cord, then turn the printer power on and test the DIMM. Back back to top How did we do? Hp 2055 Firmware Update Action NOTE: Press the ? (help) button for detailed information about clearing the jam.

Whenever the printer is ready, not busy, and has no pending warning messages, the status message “Ready” is displayed if the printer is online. Also check motor cable connections. Action If the incorrect size was selected, cancel the job or press the Help (?) button to gain access to help. navigate here You may need to reseat the memory DIMM's or replace the firmware DIMM or formatter board.

If the above action does not solve the issue, contact HP or authorized service provider. Action Turn the printer power off and then turn the printer power on. Make sure the locks on each side of the DIMM snap inward into place. (To remove a DIMM, the locks must be released.) CAUTION: Do not move or remove the DIMM It causes static electricity, which can, in turn, cause paper jams.

If you are printing from tray 1, verify that the correct paper size is selected in the control panel. 4. Sometimes the controller card can stop working and changing slots can be a fix. You can try reprinting the job to see if it was a temporary error. 3. May be feed problem.

These can be set within the Remote Control Panel. If the message persists, replace the formatter or firmware DIMM. 66.XX.YY [TYPE] FAILURE alternates with CHECK CABLES AND CYCLE POWER An error occurred in an external paper-handling device. 1st X = Back back to top How did we do? Figure 21: Removing the paper If the paper has torn, or you still cannot remove it, click here for more information about clearing jams from the fuser area Reinstall the fuser

You can remedy this by replacing the paper guide plate assembly, RG5-2248-030. Caution needs to be used when installing the new assembly - be careful of the sensor flag spring! 5Si - Can be caused by field replaceable units (FRU's) not installed correctly. Action Contact HP or an authorized service provider. Remove and reseat the optional interface card.

Verify the stacker or stapler/stacker is installed correctly and that its electrical connector is seated in the connector on the printer. Firmware updates are available for some machines at http://hp.com and clicking on the drivers and software tab. The ON setting causes the message to appear on the printer control panel display, and the printer goes offline for 10 seconds, before returning online if an error occurs that prevents Remove any paper found.

If so, reinstall the duplexer.