Home > Error Codes > Hp 5100 Error Codes

Hp 5100 Error Codes

Contents

Error 21 Print Overrun The print job is to complex. Defective Formatter PCA - Replace with known operational board and try again. Disconnect the power cord from the rear of the product. Press GO to resume printing. have a peek here

Remove any obstructions from under and around the carriage. Remove the printhead and insert the printhead again. Use both hands to pull any whole sheets of paper to avoid tearing them. Figure 48: Remove the cartridge CAUTION: Do not touch the copper-colored contacts or ink nozzles. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c01386384

Hp Laserjet 5100 Error Codes

Step three: Check the ink levels Ink level indicators appear in the middle of the diagnostic page. On the 4/4M/4+ and 5: The print job is to complex, enable page protect from the control panel and from the software. Replace the memory chip cable/connector or the DC controller.

Back back to top How did we do? Is the software set for the size you're using? Configure is properly. On flash-memory-based products, you can update the firmware code by downloading the latest flash executable file for the product and running the program according to the readme instructions posted with the

Technicians answer the phone and help customers with printer problems. Hp Designjet 5500 Error Codes Also check for any partially peeled labels, this can be a disaster if they come off inside the printer. Press the Power button () to turn on the product. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=c00013363 Step two: Print a self-test report Print a self-test report to make sure that the hardware functions correctly.

Disconnect the USB cable from the rear of the product. Solution one: Turn the printer off and on again Follow these steps to turn the product off, and then on again to reset the print mechanism. First perform the action indicated in the message. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting.

Hp Designjet 5500 Error Codes

The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printer’s electrical specifications. 55.xx PRINTER ERROR alternates with CYCLE POWER his explanation Open the top cover. Hp Laserjet 5100 Error Codes Use both hands to pull any whole sheets of paper to avoid tearing them. Issue: The Resume light and the Print Cartridge light are blinking In this error condition, the following light pattern displays on the control panel: Print Cartridge status light: Blinking Resume light:

If worn, replace. navigate here Error 18 MIO Not Ready The printer is not connected to a LAN when it's expecting to see a LAN. Press the Resume button () four times. XX05 Replace The printer has detected an incorrect ink cartridge.

PrinterTechs.com 608-831-2396 or 866-352-7108 About Us Contact Us Search Products Search Support All Products PrintersHewlett PackardLexmarkCables and Misc.JetDirect CardsBrotherKyoceraDell Toner Maintenance Kits Printers Parts Tech Support Account Login Shopping Cart My and may not be used without advance written permission of PrinterTechs.com, Inc. Solution five: Perform a power reset Follow these steps to reset the product. http://upintheaether.com/error-codes/ibm-ps2-error-codes.php Use both hands to pull any whole sheets of paper to avoid tearing them.

Wait at least 15 seconds. Error 58 4/4L/4P/4V/5/5P Check the fan cable - reseat cable or replace fan 4V/4MV Defective DC controller board - replace IIISi/4Si Error 58.1 & 58.2 Improperly seated paper cassette 4Si/IIISi 58.1/58.2 Step two: Clear the paper jam from the rear of the printer Choose from the following options to clear a paper jam from the rear of the product.

Check your product warranty to determine if your product is still under warranty, and then go to Contact HP Support to schedule a repair or replacement.

Sign Up Login Add Question cupbien asked May 24, 2007 at 3:15am 0 HP LaserJet 5100 HP 5100 Error 57.1 I have HP 5100 machine now it display Error code 57.1 Solution one: Restart the printer Press the Power button () to turn off the product, and then press it again to turn on the product. Right-click the icon for your HP product, and then click Printer Preferences. Use both hands to pull any whole sheets of paper to avoid tearing them.

ERROR 80 80X.YYYY ALL Printers The EIO card in slot X has encountered a critical error -power cycle, reseat card then replace card if needed. top Printhead cleaner error messages Status Numbers XX ranges from A0 to B5 Printhead Head Cleaner Message Description Procedure XX03 Replace The printhead cleaner installed is not recognized by the printer. Back back to top How did we do? this contact form You can depress these by hand and hear them click.

Disconnect the power cord from the rear of the product. X description: 1 = Scanner startup error 2 = Scanner rotation error 1. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting.