Hp 4 Plus Error 51
Improper laser shutter operation. 3. Error 79 can also be caused by incorrect memory addressing to a font cartridge or memory card. If it is not within the proper range, replace the fuser. LJ 5100 A temporary printing error occurred.
Adjust the output knob to the correct (9 o'clock) position and press Continue to resume operation.* The HP LaserJet IIISI, 4SI,and 4Si MX printers will display this message if the optional There may be a problem with connection between the memory chip and DC controller. Replace the DC controller. 52.X PRINTER ERROR The laser scanner speed is incorrect. Clean the optics with a soft brush or lens tissue.
Hp Laserjet 500 Mfp M525 Error Codes
Defective DC controller. 3. Is the software set for the size you're using? Not one of them had a bad connection and it was always replacing the laser/scanner or lubing the motor within the laser/scanner that got the printer working again.
Replace main motor IIIP/IIP+/IIP Error 57-1 Incompatible memory can be either top or bottom slot. Replace the D.C. Turn the power off and wait 30 seconds and turn the power back on. 3. Hp Warranty Check If the message reappears, repair service is required. 58.1 or 58.2 Error4SiAs referred to on Page 7-8 of the User's Manual, the lifter mechanism of the paper tray has failed (X:
Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance countJetDirect Reference GuideHalf-way testRepetitive defect rulerTestimonialsInnovations Rm1-6322 Can also be formatter PCA. You may need new laser unit. Debugging that is going to be interesting (read Sam's laser diode notes next :-), and I'll do the same) and I'll try to talk you through that when I know it's
If message clears, then the problem exists with the expanded memory. 63.1 Error63.2 Error63.3 Error63.4 ErrorIIISiIndicates a possible faulty expansion SIMM. Hp Support Check paper tray for overfull condition. All Rights Reserved. Plug the printer into a wall outlet and see if this resolves the problem. 2 If the printer is already plugged into a wall outlet, try another power source in the
If message persists, consult service. http://www.printertechs.com/printer-troubleshooting/hp-error-codes/195-numeric-error-codes-50-59-hp-laserjet Check the printer’s configuration. 3. Hp Laserjet 500 Mfp M525 Error Codes Replace the laser scanner ass'y HP LASER PRINTER 9000, 9040, 9050MFP 1. Hp Laserjet 600 M602 Error Codes If the error persists, replace the main motor.
Pull the sealing tape tab to remove the strip. 3. Bad cable from laser scanner ass'y to D.C. Replace the ECU. If message persists, consult service. Hp Printer Error Codes List
Back back to top How did we do? HP LASER PRINTERS 1200, 2200, 2300,2410, 2420, 2430, 3100 FAX, 3200 FAX, 4100, 4100MFP 1. On the 5L, set the Enhanced I/O to AUTO (PCL mode) and resend the print job. Temporary error. / Bad toner cartridge 2.
Error 58 4/4L/4P/4V/5/5P Check the fan cable - reseat cable or replace fan 4V/4MV Defective DC controller board - replace IIISi/4Si Error 58.1 & 58.2 Improperly seated paper cassette 4Si/IIISi 58.1/58.2 Replace the laser/scanner. 5. We tear apart, rebuild, and test HP LaserJets and LaserJet assemblies all day.
Check the cabling connections to the laser scanner assembly.3.
Look at the PrinterWorks Web site (http://www.printerworks.com/) for exploded diagrams. Replace Laser/Scanner Assembly. ERROR 59 Add Memory 4Si/IIISi Not enough memory for PostScript option. X description: 1 = Scanner startup error 2 = Scanner rotation error 1.
Cuts or kinks in fiber optic cable. 4. The DIMM that caused the error will not be used. Technicians answer the phone and help customers with printer problems. by unknown on Oct 11, 2003 at 7:57am Add comment Please sign in to comment 0 The HP4 and 4+ use different scanner assemblies.
If the error continues, turn the printer off and remove the SIMM. Also on the 4V/4MV check the door open sensor (PS402) on the terminal board located under the transfer roller. Do not refill the tray until the printer display prompts for more paper. You can reseat the connectors to the scanner assembly and the control board.
The printer can be operated until service repairs are made. Error code Y - No Yellow color HP COLOR LASER PRINTER 8500 1. Error4, 4M, 4Plus, 4Mplus, 4P, 4MP A temporary error occurred while printing. Replace if problem persists IIIP/IIP/IIP+ Paper feed problem - check feed/pickup rollers for movement and wear.
If not, find out why not. HP LASER PRINTER 3050, 3052, 3055, 3390, 3392 1. If you want to attempt board level repair try the electrolytic capacitor, C702, 10 uF 50 VDC. and may not be used without advance written permission of PrinterTechs.com, Inc.
Generally you will need to replace the laser scanner and ocassionaly the DC controller PCA Back back to top How did we do? Back back to top How did we do? The printer will still be able to print, but will only be able to use the memory below the faulty card. Back back to top How did we do?
Check connections to DC controller - replace main motor 4L/4 Main motor problem, check gear train for binding. Check -5 V, also make sure there is no interlock mechanism damage, and +5 V at J451-1 on Laser Drive PCA. Anyone have any idea what it means? Thanks Respond to this 0 An error 51 is a beam detect error related to the laser/scanner assembly.
A beam detect error or laser error.2. If the printer cannot correct the error after two seconds, a Beam Detect '51 Error' will occur.