Home > Error Code > Ibm Error Code 1701

Ibm Error Code 1701

Contents

The executing instruction may have no relation to the faulty memory. (For example if the 80287 accesses memory and triggers a parity error while running in parallel with the 80286, the System Board Errors: Code Description 101 System board interrupt failure (unexpected interrupt) 102 BIOS ROM checksum error (PC, XT); timer error (AT, MCA) 103 BASIC ROM checksum error (PC, XT); timer Boot the Advanced Diagnostics and run all the diagnostics. If you currently have a problem receiving email at your IU account, enter an alternate email address. http://upintheaether.com/error-code/ibm-jcl-error-code.php

Verify the Enable and Disable Settings 00017400 on a 90 or 95 means Bad configuration, changed device. The manual seem to be largely for the 64/256 boards. The time now is 10:09 AM. If Automatic configuration does not solve the problem, run Advanced Diagnostics. 00017900 on a 90 or 95 means NVRAM Error Log contains maximum log entries, clear system error log 000194XX Check

How Many Digits Are In A Mac Address?

I need help with a computing problem Fill out this form to submit your issue to the UITS Support Center. Sounded serious. Assuming that the diagnostics find nothing (quite likely), remove all adapters except the display card and the FD/HD controller, re-run SETUP (if necessary), and try both cold and warm boots.

A fault code of 00 indicates that no problem was found. Remember too, that a hard drive puts quite a load on these old PSUs, so check your voltages with the drive spinning. The modification is in the upper left hand corner (component side); one trace is cut on the printed side and one wire add component side. 1814 Enable/Disable could not be set Parity Error Message It's incredibly huge, heavy and generally impressive!

I removed all cards and tested the shorted line again. Ibm Error Codes Excellent!! Doing this makes me remember how much fun it was (-NOT) with all this non-plug and play-type PC technology in the 1980s! Go Here No change.

Software. Ibm Checkpoint Codes PS/2 - Diskette drive or controller error PCC - Diskette controller or drive failure 602 Diskette test failed PS/2 - Diskette boot record error 604 Non-Media Sense Diskette Drive Installed 604 Disks made in A: could be used in B: and vice versa? Furthermore, I knew this board was ok, as I'd tested it before.

Ibm Error Codes

Another common cause of the C0000005 error -- you have an advanced video adapter (8514/A, XGA, Image Adapter) installed and configured under OS/2, but your display is plugged into the planar http://www.techadvice.com/tech/P/POSTcode.htm This process passed with no hiccups. How Many Digits Are In A Mac Address? It was a good start though. 162 Configuration Error Ibm Server X3650 I now found the machine couldn't even recognise the hard drive?

If external power is supplied during the warning, the blinking stops and normal processing is restored. get redirected here I booted up the formatting utility and selected "1". I know 1701 is the POST error for hard disk parity failure. If problem persists after all cards except Fixed Disk adapter, or the primary display adapter, then the system board is failing. What Dos Command Do You Use To Erase A Hard Drive And Make It Bootable?

The INDEX identifies the selector (if any) that is associated with the exception. Page 1 of 3 123 Last Jump to page: Results 1 to 10 of 26 Thread: XT Hard Drive shows 1701 error on ROM low level format utility Thread Tools Show Anyway, I had to be very careful I didn't damage anything when desoldering. navigate to this website If it still has the original Xebec controller installed, then there is no low-level format utility in ROM.

Tantalum capacitors extracted for testing The fix I tucked the protruding leg of the good capacitor back in and resoldered. Ibm Post Error Codes This is how I remember the 8088 machines! A check of the cable revealed damage.

I figured I needed to give it a low-level format and take it from there.

I just may not have got the configurations right. If a 20-MHz board is installed, and the processor is not a 487SX, verify that the jumper is in positions 2 and 3. (487SX is indicated on the processor.) 000104XX on Each time you use the SENDSite subcommand, it is toggled on and off. Post Error Codes List Skip to: content search login Indiana University Indiana University Indiana University Knowledge Base Menu Home Menu About us Knowledge Base Search Log in Options Help 15 50 100 300 results per

Clear the system error log and restart the system. 190 (PS/2) System board error 191 (PS/2) Failed 82385 cache test 192 (N51) Lid switch error (Thinkpad) Voltage converter error 193 (PS/2) A mismatch in the number of heads will cause the failure you describe. As a computer technician, I rely on documentation to guide me through these types of messages. http://upintheaether.com/error-code/ibm-db2-error-code.php It's name escapes me right now.

Time for some serious fault finding. If the error code is not zero, it is interpreted as follows :- | EX | I | TI | INDEX | ----------------------------- The EX (external) bit is set when the If a 20-MHz board is installed, and the processor is a 487SX, verify that the jumper is in positions 1 and 2. (487SX is indicated on the processor.) 01293000 (Fatal) - According to the PCC (PC Convertible) Tech.

I believe there were two models of the Xebec controller; the original one which only supported the 10 MB drive, and then a later version which supported either 10 or 20 Multifunction card Cleaning, reassembling and testing Cleaning can be a chore but the results are well worth it. Alternately this could be a DOS error -- see above on internal stack overflow Also, it is possible that a PS/2 113 error can arise from certain programming routines used with I wonder if this would lead to a situation where the C: drive is listed as absent, even though the machine could see it before (perhaps before I unplugged drive B)?

Figure 2. Everything came up fine. If a low-battery condition is detected and external power is being supplied during power on, either a low-battery icon is displayed prior to an IPL or two short beeps are issued What could cause a short like this?

The first part of the error code indicates the device that is causing the trouble.