Home > Error Code > Hp Laserjet Iip Plus Error 41

Hp Laserjet Iip Plus Error 41

Contents

XX Description 00 memory error on the cartridge or 01 memory device not found 10.00.00 Black print cartridge 10.00.01 Cyan print cartridge 10.00.02 Magenta print cartridge 10.00.03 Yellow print cartridge Supplies Top cover open. 2. is between 0000J00000 and 2949J2222 2. I was able to find this great solution by fellow Community member @Cheetah12:First, I would recommend restarting the Print Spooler on your computer: Source: Print Jobs are Stuck in the Print http://upintheaether.com/error-code/hp-laserjet-iip-error-41.php

Replace laser scanner assy Replace DC controller PCB LJ4, 4+ Check and reseat laser/scanner cable connections Replace laser scanner connections 4L, 4P, 5P Reseat scanner assembly Replace laser/scanner assembly 53 Error Thank you and your firm again, you were terrific. Power printer off/on Excessive memory. Back back to top How did we do? http://www.fixyourownprinter.com/posts/14142

Hp Printer Error Codes List

What about the folds when output is in the top tray? - Anonymous 0 If you were to click the link that Trev gave you, you would find a Pickup kit Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. Press GO to resume printing.

Replace PS1 if defective. 2. is between 2925J00000 to 3047J999999. (2-diode to 3-diode upgrade corrects static caused problem.) IIP, IIP+, IIIP Only: 1. Check the MIO card, remove, clean contacts, reinstall. Hp Printer Error Code List Pdf May need to reload your PostScript print driver file.

Improperly seated SIMMs or font cartridge - remove, check/clean contacts re-install and try again. Hp Laptop Error Codes Cycle power to printer Bad formatter PCB LJ4, 4+, 4P NVRAM not initialized. Can also be DC controller. 5Si/4+/4Si/IIISi (X=2, 3 or 4) Fan motor faulty, check fan number X or duplexor fan and replace as necessary 5 Main motor failure - replace main You can find a good replacement in the Cartridges section of the site. - moe 0 I have a new laptop running Vista.

Optional I/O card is not connected to an active LAN. 3. Hp Error Code Oxc4eb827f Replace cable, fuser to DC Controller (P/N RG1-0907-000) II, IID, III, IIID Only: 1. Replace Interface/Formatter PCA. Replace this as an assembly.

Hp Laptop Error Codes

Sensor Arm Stuck or Broken - check for free movement of the sensor arm. The DC Controller and Laser have been replaced and the problem still exists. Hp Printer Error Codes List If you need a replacement memory card, click on my name to email me for pricing/ordering info. Hp Computer Error Codes Replace memory PCB 53-2 - Error in rear memory slot.

Check PS501 and PS106 (only on the Laserjet 4100) 13.6 Paper stopped jam at fuser. 13.10 Paper jam in Duplexer. http://upintheaether.com/error-code/hp-laserjet-error-codes.php Replace DC controller. Replace High-Voltage Power Supply. 20 ERROR/MEM OVERFLOW/INSUFFICIENT MEMORY 1. We do. Hp Inkjet Printer Error Codes

Check the HP paper specification guide for more info. Check DC Power Supply voltages or replace DC Power Supply. 3. Note IIISi/4Si: Short cp005 on DC Controller to bypass Error 50 time delay. (The printer must be turned off.) 5Si/4000/4050/4100/5000/8000/8100 Only: The fuser is malfunctioning. 50.1 Fuser low temperature failure. 50.2 http://upintheaether.com/error-code/hp-laserjet-4-error-41.php Welcome visitor number since 10/17/1997 02 Warming Up (If longer than 3 minutes) Also see error code 50. 2686A/D Replace DC power supply/Main motor driver assy.

Paper path door open. 2. Hp Printer Error Code 79 Yet, when using the "top output path", there is a crumpling noise as the paper feeds through the machine and the last two to three inches of the paper are deformed May be feed problem.

Look for bits of paper lodged in the path particularly around the sensors. 4L/4P printers can have paper stuck in the pickup area which is accessed by removing the screw over

The chances are that it's on it's way out. Occasionally the contact for the micro switch will get bent and will have to be replaced. not sure if it's related or not.now, it barely begins to power up (fan comes on), but then just shuts itself off. Hp Printer Error Code 0x610000f6 ERROR 50.XXXX - ERROR 51 (Loss of beam detect) This is a beam detect error indicating a problem with the laser scanner.

All the above actives may result in the deletion or corruption of the entries in the windows system files. Not that the optional lower cassette would help . . . Thank you for the speedy shipment and response. http://upintheaether.com/error-code/hp-laserjet-80-x-error.php msn - windows messenger video 5.

Check PS102 and PS103 13.5 Paper delay jam at fuser. looks like i'll have to take everything apart to get to it, just as in replacing the scanner motor.wally - wallytoo 0 I should have one. Please DO NOT Email for assistance in troubleshooting problems. Make sure fuser is correctly seated to AC Power PCA. 2.

Check front panel settings. 3. Replace laser PCB II, IID Replace memory PCB III, IIID 53-1 - Error in front memory slot. Note 2686D: If one clutch needs re-greasing it is likely that they all do. 4.